https://campervanvanmotorhome.com Wed, 29 Apr 2026 02:04:36 +0000 en-US hourly 1 https://wordpress.org/?v=4.1.1 https://campervanvanmotorhome.com/2026/03/skylight-roof-vent-camper-van-motorhome-horsebox-caravan-black-420x420mm/ https://campervanvanmotorhome.com/2026/03/skylight-roof-vent-camper-van-motorhome-horsebox-caravan-black-420x420mm/#comments Wed, 04 Mar 2026 08:16:45 +0000 https://campervanvanmotorhome.com/2026/03/skylight-roof-vent-camper-van-motorhome-horsebox-caravan-black-420x420mm/







HIGH QUAILTY CAMPER VAN MOTORHOME HORSEBOX CARAVAN SKYLIGHT ROOF VENT 420mm x 420mm. This premium quality camper van skylight roof vent provides additional ventilation and natural light to your motorhomes making it an ideal accessory. Made from high quality materials, our roof vents provide you with protection from UV rays as well as high impact. Blackout blinds are also supplied alongside flynet screen providing you with protection and privacy from insects. Built in 12v Turbo Fan. Roof Vent Size is 420mm x 420mm. Manufactured with high quality materials. NOTE: THE CUT-OUT SIZE SHOULD BE 355MM X 355MM. Place the internal cap (garnish) on top the roof and draw a template using a felt tip, then add another 5mm to the top and left side. Drill pilot holes in each corner and cut along the template line. Be certain to avoid ribs, braces, and electrical wiring (internally). Check that the internal cap fits through the aperture If not, cut out opening as needed and then smooth down any rough edges and primer the exposed with metal oxide paint. Make a wooden frame around the aperture to the thickness of the interned finish depth required, taking in to account the roof ply and lining. Glue the frame with Shield Stick and Seal (polyurethane) and clap in place and allow the adhesive to set. Screw the internal cap to the timber frame and seal around the lip from the top of the roof using flexible putty or Sikaflex. Place the external vent over the lip of the internal cap and mark the screw holes with a centre punch. Then remove vent from roof and drill all screw hole locations with a 1/16” pilot hole, and seal with primer paint. NOTE: If installing a power or lighted vent, provide power source of 12 volts DC, using 18-gauge wire. Place putty strips/ Sikaflex flex bead around the opening on roof. (1.27cm) from edge of opening. Be sure putty strips cover entire area to be sealed. Use double layers of putty strip or extra Sikaflex, if necessary, to seal ribbed areas. Insert vent into opening on top of putty strips. Use a screwdriver or nail to locate and line up corner drilled holes with the corner screw holes in vent frame. CAUTION: Install vent with lid hinge side toward front of vehicle. Screw corner screws first to hold vent in place then screw all remaining vent mounting screws. Tighten just enough to compress putty tape. Over-tightening may cause Plastic Base Vents to crack. Using the appropriate roof coating for your roof surface, coat screw heads and vent frame edge and seal around the frame if necessary. Your installation is complete If you are retrospectively fitting the roof vent you must take care when cutting the aperture as not to damage the existing head lining and leave enough to cover the timber frame if required. PLEASE NOTE: ALL ROOF VENTS SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN.

]]> https://campervanvanmotorhome.com/2026/03/skylight-roof-vent-camper-van-motorhome-horsebox-caravan-black-420x420mm/feed/ 0 https://campervanvanmotorhome.com/2026/02/roof-vent-fan-camper-van-motorhome-420x420mm-rv-caravan-skylight-vent-white-uk/ https://campervanvanmotorhome.com/2026/02/roof-vent-fan-camper-van-motorhome-420x420mm-rv-caravan-skylight-vent-white-uk/#comments Mon, 02 Feb 2026 19:07:45 +0000 https://campervanvanmotorhome.com/2026/02/roof-vent-fan-camper-van-motorhome-420x420mm-rv-caravan-skylight-vent-white-uk/











We are committed to resolving any issues promptly to your satisfaction. Gross weight: 2.2KG. Rated current: 1.1A. Tools Required: For installing the simplified ventilation fan, you will need a tape measure, a handheld drill, a marker pen, a drilling machine, and sealant. (Tools need to be provided by yourself). Roof Opening Size: The installation requires a roof opening of “355x355mm”. Position the fan’s flange at the roof opening (with the fan cover opening facing the rear of the RV) and trace the outline of the installation flange with a pencil. Preparing the Flange: Remove the installation flange from the neck opening and flip it over. Apply compatible sealant or filler to the bottom surface of the installation flange. Securing the Flange: Press the installation flange firmly onto the roof and secure it in place using screws. Additional Sealing: Apply additional structural adhesive around the screws and the edges of the installation flange to ensure a seamless fit. Electrical Connection: Connect the ventilation fan’s power cord to the 12V power source inside the RV using appropriate wiring. Interior Lifting Frame Adjustment: Measure the thickness of the RV’s roof. If the roof is thin or the interior trim is too long, trim the interior lifting frame to fit the roof opening height. Final Assembly: Install the interior lifting frame onto the ventilation fan from inside the RV, secure it with screws, and cover it with a cap. If replacing an existing ventilation fan, ensure all old sealant is removed and the roof opening is thoroughly cleaned and inspected for any damage or leaks before proceeding with the new installation. Use wiring with a minimum cross-sectional area of 1.5 square millimeters. Connect the red wire to the positive terminal and the black wire to the negative terminal of the power supply. Use countersunk self-tapping screws for all installations to ensure a flush finish. Please contract us firstly If there are any problems when you received the package.

]]> https://campervanvanmotorhome.com/2026/02/roof-vent-fan-camper-van-motorhome-420x420mm-rv-caravan-skylight-vent-white-uk/feed/ 0 https://campervanvanmotorhome.com/2026/01/roof-vent-skylight-camper-van-motorhome-horsebox-caravan-420x420mm-with-remote/ https://campervanvanmotorhome.com/2026/01/roof-vent-skylight-camper-van-motorhome-horsebox-caravan-420x420mm-with-remote/#comments Sat, 03 Jan 2026 17:49:43 +0000 https://campervanvanmotorhome.com/2026/01/roof-vent-skylight-camper-van-motorhome-horsebox-caravan-420x420mm-with-remote/









HIGH QUAILTY CAMPER VAN MOTORHOME HORSEBOX CARAVAN SKYLIGHT ROOF VENT 420mm x 420mm. This premium quality camper van skylight roof vent provides additional ventilation and natural light to your motorhomes making it an ideal accessory. Made from high quality materials, our roof vents provide you with protection from UV rays as well as high impact. Built in 12v Turbo Fan. Roof Vent Size is 420mm x 420mm. Manufactured with high quality materials. NOTE: THE CUT-OUT SIZE SHOULD BE 355MM X 355MM. Place the internal cap (garnish) on top the roof and draw a template using a felt tip, then add another 5mm to the top and left side. Drill pilot holes in each corner and cut along the template line. Be certain to avoid ribs, braces, and electrical wiring (internally). Check that the internal cap fits through the aperture If not, cut out opening as needed and then smooth down any rough edges and primer the exposed with metal oxide paint. Make a wooden frame around the aperture to the thickness of the interned finish depth required, taking in to account the roof ply and lining. Glue the frame with Shield Stick and Seal (polyurethane) and clap in place and allow the adhesive to set. Screw the internal cap to the timber frame and seal around the lip from the top of the roof using flexible putty or Sikaflex. Place the external vent over the lip of the internal cap and mark the screw holes with a centre punch. Then remove vent from roof and drill all screw hole locations with a 1/16” pilot hole, and seal with primer paint. NOTE: If installing a power or lighted vent, provide power source of 12 volts DC, using 18-gauge wire. Place putty strips/ Sikaflex flex bead around the opening on roof. (1.27cm) from edge of opening. Be sure putty strips cover entire area to be sealed. Use double layers of putty strip or extra Sikaflex, if necessary, to seal ribbed areas. Insert vent into opening on top of putty strips. Use a screwdriver or nail to locate and line up corner drilled holes with the corner screw holes in vent frame. CAUTION: Install vent with lid hinge side toward front of vehicle. Screw corner screws first to hold vent in place then screw all remaining vent mounting screws. Tighten just enough to compress putty tape. Over-tightening may cause Plastic Base Vents to crack. Using the appropriate roof coating for your roof surface, coat screw heads and vent frame edge and seal around the frame if necessary. Your installation is complete If you are retrospectively fitting the roof vent you must take care when cutting the aperture as not to damage the existing head lining and leave enough to cover the timber frame if required. PLEASE NOTE: ALL ROOF VENTS SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN.

]]> https://campervanvanmotorhome.com/2026/01/roof-vent-skylight-camper-van-motorhome-horsebox-caravan-420x420mm-with-remote/feed/ 0 https://campervanvanmotorhome.com/2025/10/420x420mm-camper-van-skylight-roof-vent-motorhome-horsebox-12v-fan-all-black/ https://campervanvanmotorhome.com/2025/10/420x420mm-camper-van-skylight-roof-vent-motorhome-horsebox-12v-fan-all-black/#comments Mon, 20 Oct 2025 02:00:45 +0000 https://campervanvanmotorhome.com/2025/10/420x420mm-camper-van-skylight-roof-vent-motorhome-horsebox-12v-fan-all-black/







CAMPER VAN SKYLIGHT ALL BLACK ROOF VENT 420x420mm. The camper can skylight roof vent provides additional ventilation and natural light to your motorhomes making it an ideal accessory. Made from high quality materials, our roof vents provide you with protection from UV rays as well as high impact. Blackout blinds can also be supplied alongside flynet screen providing you with protection and privacy from insects. Built in 12v Turbo Fan. Vent Size is 420mm x 420mm. Manufactured with high quality materials. NOTE: THE CUT OUT SIZE SHOULD BE 355MM X 355MM. Place the internal cap (garnish) on top the roof and draw a template using a felt tip, then add another 5mm to the top and left side. Drill pilot holes in each corner and cut along the template line. Be certain to avoid ribs, braces, and electrical wiring (internally). Check that the internal cap fits through the aperture If not, cut out opening as needed and then smooth down any rough edges and primer the exposed with metal oxide paint. Make a wooden frame around the aperture to the thickness of the interned finish depth required, taking in to account the roof ply and lining. Glue the frame with Shield Stick and Seal (polyurethane) and clap in place and allow the adhesive to set. Screw the internal cap to the timber frame and seal around the lip from the top of the roof using flexible putty or Sikaflex. Place the external vent over the lip of the internal cap and mark the screw holes with a centre punch. Then remove vent from roof and drill all screw hole locations with a 1/16” pilot hole, and seal with primer paint. NOTE: If installing a power or lighted vent, provide power source of 12 volts DC, using 18-gauge wire. Place putty strips/ Sikaflex flex bead around the opening on roof ½” (1.27cm) from edge of opening. Be sure putty strips cover entire area to be sealed. Use double layers of putty strip or extra Sikaflex if necessary, to seal ribbed areas. Insert vent into opening on top of putty strips. Use an screw driver or nail to locate and line up corner drilled holes with the corner screw holes in vent frame. CAUTION: Install vent with lid hinge side toward front of vehicle. Screw corner screws first to hold vent in place then screw all remaining vent mounting screws. Tighten just enough to compress putty tape. Over-tightening may cause Plastic Base Vents to crack. Using the appropriate roof coating for your roof surface, coat screw heads and vent frame edge and seal around the frame if necessary. Your installation is complete If you are retrospectively fitting the roof vent you must take care when cutting the aperture as not to damage the existing head lining and leave enough to cover the timber frame if required. PLEASE NOTE: ALL ROOF VENTS SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN. If there’s a problem please don’t hesitate to message us, we promise to get it resolved.

]]> https://campervanvanmotorhome.com/2025/10/420x420mm-camper-van-skylight-roof-vent-motorhome-horsebox-12v-fan-all-black/feed/ 0 https://campervanvanmotorhome.com/2025/09/roof-vent-skylight-camper-van-motorhome-horsebox-caravan-420x420mm-white/ https://campervanvanmotorhome.com/2025/09/roof-vent-skylight-camper-van-motorhome-horsebox-caravan-420x420mm-white/#comments Tue, 02 Sep 2025 19:00:14 +0000 https://campervanvanmotorhome.com/2025/09/roof-vent-skylight-camper-van-motorhome-horsebox-caravan-420x420mm-white/





HIGH QUAILTY CAMPER VAN MOTORHOME HORSEBOX CARAVAN SKYLIGHT ROOF VENT 420mm x 420mm. This premium quality camper van skylight roof vent provides additional ventilation and natural light to your motorhomes making it an ideal accessory. Made from high quality materials, our roof vents provide you with protection from UV rays as well as high impact. Blackout blinds are also supplied alongside flynet screen providing you with protection and privacy from insects. Built in 12v Turbo Fan. Roof Vent Size is 420mm x 420mm. Manufactured with high quality materials. NOTE: THE CUT-OUT SIZE SHOULD BE 355MM X 355MM. Place the internal cap (garnish) on top the roof and draw a template using a felt tip, then add another 5mm to the top and left side. Drill pilot holes in each corner and cut along the template line. Be certain to avoid ribs, braces, and electrical wiring (internally). Check that the internal cap fits through the aperture If not, cut out opening as needed and then smooth down any rough edges and primer the exposed with metal oxide paint. Make a wooden frame around the aperture to the thickness of the interned finish depth required, taking in to account the roof ply and lining. Glue the frame with Shield Stick and Seal (polyurethane) and clap in place and allow the adhesive to set. Screw the internal cap to the timber frame and seal around the lip from the top of the roof using flexible putty or Sikaflex. Place the external vent over the lip of the internal cap and mark the screw holes with a centre punch. Then remove vent from roof and drill all screw hole locations with a 1/16” pilot hole, and seal with primer paint. NOTE: If installing a power or lighted vent, provide power source of 12 volts DC, using 18-gauge wire. Place putty strips/ Sikaflex flex bead around the opening on roof. (1.27cm) from edge of opening. Be sure putty strips cover entire area to be sealed. Use double layers of putty strip or extra Sikaflex, if necessary, to seal ribbed areas. Insert vent into opening on top of putty strips. Use a screwdriver or nail to locate and line up corner drilled holes with the corner screw holes in vent frame. CAUTION: Install vent with lid hinge side toward front of vehicle. Screw corner screws first to hold vent in place then screw all remaining vent mounting screws. Tighten just enough to compress putty tape. Over-tightening may cause Plastic Base Vents to crack. Using the appropriate roof coating for your roof surface, coat screw heads and vent frame edge and seal around the frame if necessary. Your installation is complete If you are retrospectively fitting the roof vent you must take care when cutting the aperture as not to damage the existing head lining and leave enough to cover the timber frame if required. PLEASE NOTE: ALL ROOF VENTS SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN.

]]> https://campervanvanmotorhome.com/2025/09/roof-vent-skylight-camper-van-motorhome-horsebox-caravan-420x420mm-white/feed/ 0 https://campervanvanmotorhome.com/2025/08/roof-vent-skylight-camper-van-motorhome-horsebox-caravan-420x420mm-smoked/ https://campervanvanmotorhome.com/2025/08/roof-vent-skylight-camper-van-motorhome-horsebox-caravan-420x420mm-smoked/#comments Sun, 03 Aug 2025 05:43:43 +0000 https://campervanvanmotorhome.com/2025/08/roof-vent-skylight-camper-van-motorhome-horsebox-caravan-420x420mm-smoked/





HIGH QUAILTY CAMPER VAN MOTORHOME HORSEBOX CARAVAN SKYLIGHT ROOF VENT 420mm x 420mm. This premium quality camper van skylight roof vent provides additional ventilation and natural light to your motorhomes making it an ideal accessory. Made from high quality materials, our roof vents provide you with protection from UV rays as well as high impact. Blackout blinds are also supplied alongside flynet screen providing you with protection and privacy from insects. Built in 12v Turbo Fan. Roof Vent Size is 420mm x 420mm. Manufactured with high quality materials. NOTE: THE CUT-OUT SIZE SHOULD BE 355MM X 355MM. Place the internal cap (garnish) on top the roof and draw a template using a felt tip, then add another 5mm to the top and left side. Drill pilot holes in each corner and cut along the template line. Be certain to avoid ribs, braces, and electrical wiring (internally). Check that the internal cap fits through the aperture If not, cut out opening as needed and then smooth down any rough edges and primer the exposed with metal oxide paint. Make a wooden frame around the aperture to the thickness of the interned finish depth required, taking in to account the roof ply and lining. Glue the frame with Shield Stick and Seal (polyurethane) and clap in place and allow the adhesive to set. Screw the internal cap to the timber frame and seal around the lip from the top of the roof using flexible putty or Sikaflex. Place the external vent over the lip of the internal cap and mark the screw holes with a centre punch. Then remove vent from roof and drill all screw hole locations with a 1/16” pilot hole, and seal with primer paint. NOTE: If installing a power or lighted vent, provide power source of 12 volts DC, using 18-gauge wire. Place putty strips/ Sikaflex flex bead around the opening on roof. (1.27cm) from edge of opening. Be sure putty strips cover entire area to be sealed. Use double layers of putty strip or extra Sikaflex, if necessary, to seal ribbed areas. Insert vent into opening on top of putty strips. Use a screwdriver or nail to locate and line up corner drilled holes with the corner screw holes in vent frame. CAUTION: Install vent with lid hinge side toward front of vehicle. Screw corner screws first to hold vent in place then screw all remaining vent mounting screws. Tighten just enough to compress putty tape. Over-tightening may cause Plastic Base Vents to crack. Using the appropriate roof coating for your roof surface, coat screw heads and vent frame edge and seal around the frame if necessary. Your installation is complete If you are retrospectively fitting the roof vent you must take care when cutting the aperture as not to damage the existing head lining and leave enough to cover the timber frame if required. PLEASE NOTE: ALL ROOF VENTS SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN.

]]> https://campervanvanmotorhome.com/2025/08/roof-vent-skylight-camper-van-motorhome-horsebox-caravan-420x420mm-smoked/feed/ 0 https://campervanvanmotorhome.com/2025/06/420x420mm-camper-van-skylight-roof-vent-motorhome-horsebox-caravan-smoked/ https://campervanvanmotorhome.com/2025/06/420x420mm-camper-van-skylight-roof-vent-motorhome-horsebox-caravan-smoked/#comments Fri, 20 Jun 2025 04:19:41 +0000 https://campervanvanmotorhome.com/2025/06/420x420mm-camper-van-skylight-roof-vent-motorhome-horsebox-caravan-smoked/






CAMPER VAN SKYLIGHT SMOKE ROOF VENT 420x420mm. The camper can skylight roof vent provides additional ventilation and natural light to your motorhomes making it an ideal accessory. Made from high quality materials, our roof vents provide you with protection from UV rays as well as high impact. Blackout blinds can also be supplied alongside flynet screen providing you with protection and privacy from insects. Built in 12v Turbo Fan. Vent Size is 420mm x 420mm. Manufactured with high quality materials. NOTE: THE CUT OUT SIZE SHOULD BE 355MM X 355MM. Place the internal cap (garnish) on top the roof and draw a template using a felt tip, then add another 5mm to the top and left side. Drill pilot holes in each corner and cut along the template line. Be certain to avoid ribs, braces, and electrical wiring (internally). Check that the internal cap fits through the aperture If not, cut out opening as needed and then smooth down any rough edges and primer the exposed with metal oxide paint. Make a wooden frame around the aperture to the thickness of the interned finish depth required, taking in to account the roof ply and lining. Glue the frame with Shield Stick and Seal (polyurethane) and clap in place and allow the adhesive to set. Screw the internal cap to the timber frame and seal around the lip from the top of the roof using flexible putty or Sikaflex. Place the external vent over the lip of the internal cap and mark the screw holes with a centre punch. Then remove vent from roof and drill all screw hole locations with a 1/16” pilot hole, and seal with primer paint. NOTE: If installing a power or lighted vent, provide power source of 12 volts DC, using 18-gauge wire. Place putty strips/ Sikaflex flex bead around the opening on roof ½” (1.27cm) from edge of opening. Be sure putty strips cover entire area to be sealed. Use double layers of putty strip or extra Sikaflex if necessary, to seal ribbed areas. Insert vent into opening on top of putty strips. Use an screw driver or nail to locate and line up corner drilled holes with the corner screw holes in vent frame. CAUTION: Install vent with lid hinge side toward front of vehicle. Screw corner screws first to hold vent in place then screw all remaining vent mounting screws. Tighten just enough to compress putty tape. Over-tightening may cause Plastic Base Vents to crack. Using the appropriate roof coating for your roof surface, coat screw heads and vent frame edge and seal around the frame if necessary. Your installation is complete If you are retrospectively fitting the roof vent you must take care when cutting the aperture as not to damage the existing head lining and leave enough to cover the timber frame if required. PLEASE NOTE: ALL ROOF VENTS SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN. If there’s a problem please don’t hesitate to message us, we promise to get it resolved.

]]> https://campervanvanmotorhome.com/2025/06/420x420mm-camper-van-skylight-roof-vent-motorhome-horsebox-caravan-smoked/feed/ 0 https://campervanvanmotorhome.com/2025/04/jet-black-skylight-roof-vent-camper-van-motorhome-horsebox-flynet-12v-420x420mm/ https://campervanvanmotorhome.com/2025/04/jet-black-skylight-roof-vent-camper-van-motorhome-horsebox-flynet-12v-420x420mm/#comments Fri, 18 Apr 2025 21:10:00 +0000 https://campervanvanmotorhome.com/2025/04/jet-black-skylight-roof-vent-camper-van-motorhome-horsebox-flynet-12v-420x420mm/













Tani-Logics Uk Web Agency. Jet Black Skylight Roof Vent Camper Van Motorhome Horsebox Flynet 12V 420x420mm. Huge choice of stock. This skylight roof vent is ideal accessory form the motorhome, camper van or house box which require additional ventilation. It’s also ideal for venting small spaces, the built-in 12V fan provides addition ventilation. Made from superior quality impact and UV resistant materials supplied with permanent air flow ventilation system and mosquito screen. Built in 12v Fan overall vent Size is 420mm x 420mm. NOTE: THE CUT OUT SIZE SHOULD BE 355MM X 355MM. Place the internal cap (garnish) on top the roof and draw a template using a felt tip, then add another 5mm to the top and left side. Drill pilot holes in each corner and cut along the template line. Be certain to avoid ribs, braces, and electrical wiring (internally). Check that the internal cap fits through the aperture If not, cut out opening as needed and then smooth down any rough edges and primer the exposed with metal oxide paint. Make a wooden frame around the aperture to the thickness of the interned finish depth required, taking in to account the roof ply and lining. Glue the frame with Shield Stick and Seal (polyurethane) and clap in place and allow the adhesive to set. Screw the internal cap to the timber frame and seal around the lip from the top of the roof using flexible putty or Sikaflex. Place the external vent over the lip of the internal cap and mark the screw holes with a centre punch. Then remove vent from roof and drill all screw hole locations with a 1/16” pilot hole, and seal with primer paint. NOTE: If installing a power or lighted vent, provide power source of 12 volts DC, using 18-gauge wire. Place putty strips/ Sikaflex flex bead around the opening on roof ½” (1.27cm) from edge of opening. Be sure putty strips cover entire area to be sealed. Use double layers of putty strip or extra Sikaflex if necessary, to seal ribbed areas. Insert vent into opening on top of putty strips. Use an screw driver or nail to locate and line up corner drilled holes with the corner screw holes in vent frame. CAUTION: Install vent with lid hinge side toward front of vehicle. Screw corner screws first to hold vent in place then screw all remaining vent mounting screws. Tighten just enough to compress putty tape. Over-tightening may cause Plastic Base Vents to crack. Using the appropriate roof coating for your roof surface, coat screw heads and vent frame edge and seal around the frame if necessary. Your installation is complete If you are retrospectively fitting the roof vent you must take care when cutting the aperture as not to damage the existing head lining and leave enough to cover the timber frame if required. All order will be processed within 24 hr expect on weekends and national holidays. Any genuinely faulty goods will be replaced, however we must be notified of any faulty goods upon receipt of the item. As a company which prides itself on its very high standard of customer service. A store that will cater to your every need when it comes to car, van, and caravan accessories. We supply high quality products that are well sought after. When it comes to auto vehicle’s we all want to make sure we are looking for the best of quality products. Look no further and head over to our shop to find what it is you are looking for. Sign up to our newsletter for special deals.

]]> https://campervanvanmotorhome.com/2025/04/jet-black-skylight-roof-vent-camper-van-motorhome-horsebox-flynet-12v-420x420mm/feed/ 0 https://campervanvanmotorhome.com/2024/07/camper-van-skylight-roof-vent-motorhome-horsebox-all-black-420x420mm/ https://campervanvanmotorhome.com/2024/07/camper-van-skylight-roof-vent-motorhome-horsebox-all-black-420x420mm/#comments Sun, 21 Jul 2024 08:10:48 +0000 https://campervanvanmotorhome.com/2024/07/camper-van-skylight-roof-vent-motorhome-horsebox-all-black-420x420mm/







Roof Vent 14″ x 14″ (35.5cm x 35.5cm), with 12v electric fan, all BLACK. The skylight roof vent is the ideal accessory for the motorhome, camper van, or house box which requires additional ventilation. It’s also ideal for venting small spaces, the built-in 12V fan provides additional ventilation. Made from superior quality impact and UV resistant materials supplied with permanent air flow ventilation system and mosquito screen. Overall vent Size is 420mm x 420mm. The cut hole needs to be 355mm x 355mm. Instructions to fit this on. Place the internal cap (garnish) on top of the roof and draw a template using a felt tip, then add another 5mm to the top and left side. Drill pilot holes in each corner and cut along the template line. Be certain to avoid ribs, braces, and electrical wiring (internally). Check that the internal cap fits through the aperture If not, cut out the opening as needed and then smooth down any rough edges and primer the exposed with metal oxide paint. Make a wooden frame around the aperture to the thickness of the interned finish depth required, taking into account the roof ply and lining. Glue the frame with Shield Stick and Seal (polyurethane) clap in place and allow the adhesive to set. Screw the internal cap to the timber frame and seal around the lip from the top of the roof using flexible putty or Sikaflex. Place the external vent over the lip of the internal cap and mark the screw holes with a center punch. Then remove the vent from the roof and drill all screw hole locations with a 1/16” pilot hole, and seal with primer paint. NOTE: If installing a power or lighted vent, provide a power source of 12 volts DC, using an 18-gauge wire. Place putty strips/ Sikaflex flex bead around the opening on the roof ½” (1.27cm) from the edge of the opening. Be sure putty strips cover the entire area to be sealed. Use double layers of putty strip or extra Sikaflex if necessary, to seal ribbed areas. Insert vent into opening on top of putty strips. Use a screwdriver or nail to locate and line up corner drilled holes with the corner screw holes in the vent frame. CAUTION: Install vent with lid hinge side toward the front of the vehicle. Screw corner screws first to hold the vent in place then screw all remaining vent mounting screws. Tighten just enough to compress putty tape. Over-tightening may cause Plastic Base Vents to crack. Using the appropriate roof coating for your roof surface, coat screw heads, and vent frame edge and seal around the frame if necessary. Your installation is complete. If you are retrospectively fitting the roof vent you must take care when cutting the aperture so as not to damage the existing head lining and leave enough to cover the timber frame if required. All items are stored in and dispatched from the United Kingdom. Please be aware service to the aforementioned postcodes can take an additional 1-2 days including our express service.

]]> https://campervanvanmotorhome.com/2024/07/camper-van-skylight-roof-vent-motorhome-horsebox-all-black-420x420mm/feed/ 0 https://campervanvanmotorhome.com/2024/05/camper-van-skylight-boat-horsebox-camper-roof-vent-motorhome-420x420mm-jet-black/ https://campervanvanmotorhome.com/2024/05/camper-van-skylight-boat-horsebox-camper-roof-vent-motorhome-420x420mm-jet-black/#comments Wed, 22 May 2024 11:37:05 +0000 https://campervanvanmotorhome.com/2024/05/camper-van-skylight-boat-horsebox-camper-roof-vent-motorhome-420x420mm-jet-black/
















Jet Black Skylight Roof Vent 420x420mm. This skylight roof vent is an ideal accessory for a motorhome, camper van or house box which requires additional ventilation. It’s also ideal for venting small spaces, the built-in 12V fan provides additional ventilation. Made from superior quality impact and UV resistant materials supplied with permanent air flow ventilation system and mosquito screen. Built in 12v Fan. Overall vent Size is 420mm x 420mm. The cut hole needs to be 355mm x 355mm. Place the internal cap (garnish) on top the roof and draw a template using a felt tip, then add another 5mm to the top and left side. Drill pilot holes in each corner and cut along the template line. Be certain to avoid ribs, braces, and electrical wiring (internally). Check that the internal cap fits through the aperture If not, cut out opening as needed and then smooth down any rough edges and primer the exposed with metal oxide paint. Make a wooden frame around the aperture to the thickness of the interned finish depth required, taking in to account the roof ply and lining. Glue the frame with Sikaflex (polyurethane) and clap in place and allow the adhesive to set. Screw the internal cap to the timber frame and seal around the lip from the top of the roof using flexible putty or Sikaflex. Place the external vent over the lip of the internal cap and mark the screw holes with a centre punch. Then remove vent from roof and drill all screw hole locations with a 1/16?? Pilot hole, and seal with primer paint. NOTE: If installing a power or lighted vent, provide power source of 12 volts DC, using 18-gauge wire. Place putty strips/ Sikaflex flex bead around the opening on roof ½?? (1.27cm) from edge of opening. Be sure putty strips cover entire area to be sealed. Use double layers of putty strip or extra Sikaflex if necessary, to seal ribbed areas. Insert vent into opening on top of putty strips. Use an screw driver or nail to locate and line up corner drilled holes with the corner screw holes in vent frame. CAUTION: Install vent with lid hinge side toward front of vehicle. Screw corner screws first to hold vent in place then screw all remaining vent mounting screws. Tighten just enough to compress putty tape. Over-tightening may cause Plastic Base Vents to crack. Using the appropriate roof coating for your roof surface, coat screw heads and vent frame edge and seal around the frame if necessary. Your installation is complete. If you are retrospectively fitting the roof vent you must take care when cutting the aperture as not to damage the existing head lining and leave enough to cover the timber frame if required. We aim to provide our customers with the highest quality of products at the best prices. We specialise in a wide range of vehicle accessories such as car cover, seat covers, camper windows, roof vents, camper lining, plywood kits and much more. Have a look through our wide range of products, we definitely have something of interest for everyone. All orders will be processed within 24 hr except on weekends and national holidays. Orders to Isle of Wight, Isle of Man, Scottish Highlands and Northern Ireland may incur an additional surcharge depending on the item. Any genuinely faulty goods will be replaced, however we must be notified of any faulty goods upon receipt of the item. Please Note: Ply lining kits are made to order and have a lead time of 7-14 days. Please note your item will not be sent out until funds have cleared and showing into our account for transfers and cheques. Send us a Message.

]]> https://campervanvanmotorhome.com/2024/05/camper-van-skylight-boat-horsebox-camper-roof-vent-motorhome-420x420mm-jet-black/feed/ 0