https://campervanvanmotorhome.com Thu, 14 May 2026 03:08:12 +0000 en-US hourly 1 https://wordpress.org/?v=4.1.1 https://campervanvanmotorhome.com/2026/02/camper-van-motorhome-split-charge-relay-kits-12v-140a-digital-vsr-sense/ https://campervanvanmotorhome.com/2026/02/camper-van-motorhome-split-charge-relay-kits-12v-140a-digital-vsr-sense/#comments Wed, 11 Feb 2026 07:24:44 +0000 https://campervanvanmotorhome.com/2026/02/camper-van-motorhome-split-charge-relay-kits-12v-140a-digital-vsr-sense/


Camper Van Motorhome Split Charge Relay Kits 12V 140A Digital VSR Sense. 3mtr 12v Leads Split Charge Relay Kit with 12V 140amp Intelligent Voltage Sense Relay. This kits is suitable for safely charging up to 220AH Leisure batteries. This kits is suitable for Camper Vans, Motor homes, 4x4s, Day Vans, Mobile workshops, Cars or Boats. Voltage sense systems are especially suited for modern vehicles with canbus controlled wiring as this type of kit does not need an ignition feed or any additional wiring and are very simple kit to install, all you need to do is to connect your starter battery to your leisure battery(s) by using the kit supplied, with very easy to understand fitting instructions and a wiring diagram. The voltage sense relay simply detects the rise in voltage from you vehicles charging system to allow you to charge your leisure battery(s) while your engine is running. When your engine is switched off, the relay will isolate your leisure battery(s) from your main starter battery. So it does not drain your main starter battery and you will always be able to start your vehicle. Please note: The 3 mtrs of Red cable supplied in this kit are made up of the 4 separate leads which is ready made with connectors&heat shrink tubes. The kit includes everything you need for setup dual battery charging system. 12v 140amp Intelligent Voltage sense Split Charge Relay. 2 x 250mm RED 70amp READY MADE cable from Battery to fuse holder lead. 1 x 500mm RED 70amp READY MADE cable Relay to fuse holder lead. 1 x 2 metre 70amp Relay to fuse holder READY MADE Lead. 1 metre 70amp of READY MADE Black Earth Lead. 1 Pair 8mm Post Type Battery Terminals. 2 x MTA MIDI Fuse holders. 4 x 60A MTA MIDI Fuses including 2 spares. Red&Black Heat shrink to protect all the connections. 10 x adhesive cable tie fixings base to keep everything tidy. Easy to understand Fitting Instructions + after sales support if required. We appreciate your business and strived to improve our customer service and our commitment to quality.

]]> https://campervanvanmotorhome.com/2026/02/camper-van-motorhome-split-charge-relay-kits-12v-140a-digital-vsr-sense/feed/ 0 https://campervanvanmotorhome.com/2025/07/leisure-battery-split-charge-relay-kit-12v-140a-vsr-for-camper-van-motor-homes/ https://campervanvanmotorhome.com/2025/07/leisure-battery-split-charge-relay-kit-12v-140a-vsr-for-camper-van-motor-homes/#comments Tue, 22 Jul 2025 05:09:30 +0000 https://campervanvanmotorhome.com/2025/07/leisure-battery-split-charge-relay-kit-12v-140a-vsr-for-camper-van-motor-homes/


Leisure Battery Split Charge Relay Kit 12V 140A VSR For Camper Van Motor homes. SMART BATTERY ISOLATOR INSTRUCTIONS. Dual Battery Isolators / Voltage Sensitive Relays have been specifically designed for a wide variety of 12V applications. Dual Battery lsolators sense the input voltage generatedand automatically connect/disconnect the appliance or circuit at pre-set voltages, eliminating the possibility of discharging the primary starting battery. Constructed with a weatherproof body (IP65) and durable silver tipped contacts. Dual Battery Isolators also feature surge protection and a L. D indicator designed to alert the user when the unit is engaged. Dual Battery Isolators are ideal for dual battery set-ups asthey enable two batteries to be charged at the same timeand then isolates the batteries from each other when the vehicle is turned off, ensuring your starting battery isalways charged and ready to go. Designed for dual battery systems. Suitable for most 12V charging systems- Surge protection. Easy to install. Automatically sensing voltage level of main battery. Cut In Voltage: 13.3V. Cut Out voltage: 12.8V. Emergency Charge Function. This type of kit is suitable for Camper Vans, Motor homes, 4x4s, Day Vans, Mobile workshops, Cars or Boats(euro 6 vehicle which have smart alternator may not suitable). Voltage sense systems are especially suited for modern vehicles with canbus controlled wiring as this type of kit does not need an ignition feed or any additional wiring and are very simple kit to install, all you need to do is to connect your starter battery to your leisure battery(s) by using the kit supplied, with very easy to understand fitting instructions and a wiring diagram. The voltage sense relay simply detects the rise in voltage from you vehicles charging system to allow you to charge your leisure battery(s) while your engine is running. When your engine is switched off, the relay will isolate your leisure battery(s) from your main starter battery. So it does not drain your main starter battery and you will always be able to start your vehicle. 3mtr 12v Split Charge Relay Kit. Package Includes: (You will be supplied with everything you need to fit this kit). 12v 140amp Intelligent Voltage sense Split Charge Relay. 2 x 250mm RED 70amp READY MADE cable from Battery to fuse holder lead. 1 x 500mm RED 70amp READY MADE cable Relay to fuse holder lead. 1 x 2 metre 70amp Relay to fuse holder READY MADE Lead. 1 metre 70amp of READY MADE Black Earth Lead. 1 Pair 8mm Post Type Battery Terminals. 2 x MTA MIDI Fuse holders. 4 x 60A MTA MIDI Fuses including 2 spares. Red&Black Heat shrink to protect all the connections. 10 x adhesive cable tie fixings base to keep everything tidy. Easy to understand Fitting Instructions + after sales support if required. 5mtr 12v Split Charge Relay Kit. 2 x 250mm RED 70amp READY MADE cable from Battery to fuse holder Leads. 1 x 500mm RED 70amp READY MADE cable Relay to fuse holder Leads. 1 x 4 metre 70amp Relay to fuse holder READY MADE Leads. 1 metre 70amp of READY MADE Black Earth Leads. 7mtr 12v Split Charge Relay Kit. 1 x 6 metre 70amp Relay to fuse holder READY MADE Leads. 5M Split Charge Relay Kit with 6way fuse box. 6way Fuse Box with 12 fuse blades & Label Stickers. 2x 200A Battery Isolator Switch with two keys. 2 x MTA Midi Fuse holders. 4 x 60A MTA Midi Fuses including 2 spares. 10 x Cable Crimps Terminals Connectors. Heat shrink to protect all the connections. We appreciate your business and strived to improve our customer service and our commitment to quality.

]]> https://campervanvanmotorhome.com/2025/07/leisure-battery-split-charge-relay-kit-12v-140a-vsr-for-camper-van-motor-homes/feed/ 0 https://campervanvanmotorhome.com/2025/06/200w-solar-charging-kit-20a-charge-controller-camper-van-caravan-motorhome-bo/ https://campervanvanmotorhome.com/2025/06/200w-solar-charging-kit-20a-charge-controller-camper-van-caravan-motorhome-bo/#comments Tue, 01 Jul 2025 03:59:19 +0000 https://campervanvanmotorhome.com/2025/06/200w-solar-charging-kit-20a-charge-controller-camper-van-caravan-motorhome-bo/


200w Solar Charging Kit 20a Charge Controller Camper Van Caravan motorhome Boat Yacht. 100W+100W solar charging kit. 2 x 100W high efficiency waterproof monocrystalline solar panels, each with 5m cable and MC4 connectors. Advanced 20A solar charge controller with LCD display and powerful 2.4A dual USB output. 2 x 100W solar panels. This 200W system is perfect for permanent outdoor use to provide free electricity for charging 12V batteries to power various applications such as in a camper van, motorhome, boat, shed, farm, as well as remote applications such as telecommunications or monitoring equipment. It can also be used to provide a direct power supply for applications not sensitive to changes in input voltage / current e. Electric motors or pumps. 100w Specifications (per solar panel). Maximum power voltage: 20.2V. Maximum power current: 4.95A. Open circuit voltage: 23.9V. Short circuit current: 5.26A. Power allowance range: +/- 3%. Dimensions: 845 x 670 x 30mm. 4 mounting holes 9 x 11 mm. 2 x 5m of high quality single core solar cable 4.0mm cross section. Male and female MC4 connectors attached (can be cut off when wiring to the solar controller). Each panel is fitted with 5m of special solar cable which can work at high roof temperatures, with minimum power losses. A pair of male / female MC4 connectors are crimped on the end of cable for easy connection to other solar panels, extension leads or to your existing system (the MC4 connectors can also be cut off when wiring to the screw terminals of a solar charge controller). The long-lasting, high-efficiency monocrystalline solar cells and the tough, sealed, aluminium frame will provide years and years of consistent, free power. The waterproof design ensures that the panels can be used in all weather conditions. These panels also feature innovative 5 busbar solar cells, which are more efficient than the 2, 3 or 4 busbar solar cells used in most other solar panels, and are able to extract more power from the same surface area. This results in smaller overall solar panels, which are ideal for applications where space is limited. These solar cells are also the best choice for applications in warmer climates, as they operate well even in high ambient temperatures. Advanced 20A solar charge controller. The kit includes a 20A 12V/24V Photonic Universe solar charge controller designed to protect batteries whilst charging them, with automatic cut off to prevent over-charging and deep discharge. PWM (Pulse Width Modulation). Technology which increases charge acceptance and prolongs the life of your battery. Often PWM technology can recover some lost battery capacity. Fully automated operation and auto 12/24V selection. Rated charge/discharge current: 20A. Maximum solar panel input power: 320W (12V) / 640W (24V). Maximum solar panel input voltage 50V. Temperature sensor for automatic compensation: -3mV/C/2V (25C). Working temperature: -25ºC to +55ºC. 9.2mA (12V);? 11.7mA (24V). 3 pairs of terminals (solar, battery, optional load). Terminals for wire up to 10mm. Multiple mounting holes for ease of installation. Size: 16 x 9.5 x 5 cm. This controller stops reverse current at night (from the battery back to the solar panel) so your battery won’t lose any charge. It has many other protection functions such as over charge / discharge, over load, short circuit, overheating etc. The LCD display shows information regarding real time solar panel and battery performance, including: voltage, current, battery state of charge, and battery temperature. An energy statistics counter also displays the accumulated daily and monthly charge values (useful for comparing solar panel performance between different periods). This solar charge controller also offers the rare and highly sought-after feature of a dual USB charging output. These 5V USB ports have a total combined output of 2.4A, offering fast and powerful charging of USB compatible devices such as mobile phones, tablets, mp3 players etc. An optional programmable load e. 12V lighting / fans / water pumps may also be connected directly to the solar charge controller. Using the buttons and LCD display, the user can set personalised On/Off timers for these appliances. In addition, this controller also offers various charging programs for different battery types, which can be easily selected by the user. In addition to the built-in temperature sensor, the controller has a pair of terminals for connecting a. Which can be attached directly to the battery to measure the battery temperature more precisely and optimise the charging process. Please note: This is an essentials kit and does not include mounting accessories or battery cable. UK Bussiness with UK Stock. Where we show a link to a Technical Sheet to download please. And we can send you one. Don’t like links to outside pages so sadly they don’t work. We like to offer. If so it will be sent out on a 1 to 2 day service. All are track and traceable We like to use, the Post Office, DPD, DHL and other major carriers. Outside the UK Mainland also carry a small extra charge, pop in your Postcode to see. If not we do it the very next day. Some kits, Solar Panel and Charge Controller for example may be delivered by two different couriers. We send out parcels Monday to Friday. We will then send one to you by post. Who are Eos Solar Solutions? Eos Solar Solutions are a. True Solar and Wind Energy Company. We specialize in On Grid and Off Grid systems. We like Solar and Wind energy. We can design and assist in the design of Home and Industrial systems. We can also help where you are in remote and mobile locations, small workshops, home systems and man caves. We also have solutions for campers, camping, small sheds, workshops, marine and allotments. We have been trading in Solar and Wind for years, do confuse us with others.. Be assured, Solar and Wind is what we do… Please consider this when checking prices and the support as we offer qualified. Just ask via the. We are based in the UK with the stock. When checking prices please note you will get the product in days not weeks. Get an invoice for. Because the products are sent from the UK. Eos Solar Solutions Northampton NN3. On the Internet We are on the Internet, search for “Eos Solar Solutions” and find us. We are a member of Solar Energy UK, a UK Government recognised group of Solar suppliers and installers. Again consider this when purchasing products. We like good feedback, so if something is not as you expected then message us as everything can be resolved. It would need to be as new with minimal damage to the packaging. Please inform us if you plan to return the item.

]]> https://campervanvanmotorhome.com/2025/06/200w-solar-charging-kit-20a-charge-controller-camper-van-caravan-motorhome-bo/feed/ 0 https://campervanvanmotorhome.com/2025/03/30a-pwm-lcd-usb-solar-charge-controller-x10-value-pack-10pc-motorhome-camper-van/ https://campervanvanmotorhome.com/2025/03/30a-pwm-lcd-usb-solar-charge-controller-x10-value-pack-10pc-motorhome-camper-van/#comments Wed, 19 Mar 2025 20:08:45 +0000 https://campervanvanmotorhome.com/2025/03/30a-pwm-lcd-usb-solar-charge-controller-x10-value-pack-10pc-motorhome-camper-van/










VALUE TEN PACK (10pcs). High efficiency PWM Solar charge controller / regulator. Also featuring twin USB charging ports for phones etc. 30 amp charge controller suitable for solar PV panels upto a maximum of 390 watts at 12 volts. Wide Compatibility: The solar charger controller with 30A rated discharge current is compatible with 12V or 24V system automatically, suitable for lead-acid batteries: OPEN, AGM, GEL. Dual USB 5V output ports support mobile phones, tablet PCs or other devices that require 5V voltage. Reliable Protection: The solar charge regulator provides over-current protection, short-circuit protection, inverse connection protection, low voltage and overcharge protection, a reliable protector for your devices. Intelligent: Built-in industrial microcontroller for automatic management, memorizing various parameters set by the user and the data won’t be lost when the battery runs out. The solar controller will turn off automatically once the voltage is too low. Functional LCD Display: Intuitive LCD display that can clearly indicate the status and data is able to switch modes and parameter configuration, suitable for home, industrial, commercial, etc. Easy to Use: The charge controller should connect to the battery first, then the solar panel, and finally the load! You can change the settings by the simple one-button operation. The manufacturers say these are suitable for 12 or 24v operation, we prefer to market and use them for 12v only. In the past with budget autodetect controllers we have found should the battery become disconnected with a 24v panel connected and in the sun damage can be caused. Coastline Campers aim to offer top quality products accessories, help and advice along with superb after sales service. We have been involved in Electronics, Communications, Motorhomes and Motorsport for many years and have gathered wealth of knowledge relating to Auto Electric’s, Solar power, Panel wiring, etc. This includes items for Caravans, Motorhomes, Boats, Fishing, Motorsport, Kit Cars, Garages etc. We are also more than happy to offer advice on suitability and installation of our products. Please keep checking our shop, as there are many more products to be added in the near future. We would also welcome your suggestions as to other products that you would like to see listed. Please ensure your details are correct. For Scottish Highlands, Islands and Non mainland Britain please ask us whether there is an additional cost before purchasing. Our aim is to provide an excellent service and this includes describing items for sale as accurately as possible. Please take a few moments to read all of the details, to make sure that the item you are ordering is exactly what you require. We are more than happy to answer any questions regarding these items and their suitability for your intended use.

]]> https://campervanvanmotorhome.com/2025/03/30a-pwm-lcd-usb-solar-charge-controller-x10-value-pack-10pc-motorhome-camper-van/feed/ 0 https://campervanvanmotorhome.com/2024/11/10a-pwm-lcd-usb-solar-charge-controller-x10-value-pack-10pc-motorhome-camper-van/ https://campervanvanmotorhome.com/2024/11/10a-pwm-lcd-usb-solar-charge-controller-x10-value-pack-10pc-motorhome-camper-van/#comments Wed, 20 Nov 2024 07:41:20 +0000 https://campervanvanmotorhome.com/2024/11/10a-pwm-lcd-usb-solar-charge-controller-x10-value-pack-10pc-motorhome-camper-van/









VALUE TEN PACK (10pcs). High efficiency PWM Solar charge controller / regulator. Also featuring twin USB charging ports for phones etc. 10 amp charge controller suitable for solar PV panels upto a maximum of 130 watts at 12 volts. Wide Compatibility: The solar charger controller with 10A rated discharge current is compatible with 12V or 24V system automatically, suitable for lead-acid batteries: OPEN, AGM, GEL. Dual USB 5V output ports support mobile phones, tablet PCs or other devices that require 5V voltage. Reliable Protection: The solar charge regulator provides over-current protection, short-circuit protection, inverse connection protection, low voltage and overcharge protection, a reliable protector for your devices. Intelligent: Built-in industrial microcontroller for automatic management, memorizing various parameters set by the user and the data won’t be lost when the battery runs out. The solar controller will turn off automatically once the voltage is too low. Functional LCD Display: Intuitive LCD display that can clearly indicate the status and data is able to switch modes and parameter configuration, suitable for home, industrial, commercial, etc. Easy to Use: The charge controller should connect to the battery first, then the solar panel, and finally the load! You can change the settings by the simple one-button operation. The manufacturers say these are suitable for 12 or 24v operation, we prefer to market and use them for 12v only. In the past with budget autodetect controllers we have found should the battery become disconnected with a 24v panel connected and in the sun damage can be caused. Coastline Campers aim to offer top quality products accessories, help and advice along with superb after sales service. We have been involved in Electronics, Communications, Motorhomes and Motorsport for many years and have gathered wealth of knowledge relating to Auto Electric’s, Solar power, Panel wiring, etc. This includes items for Caravans, Motorhomes, Boats, Fishing, Motorsport, Kit Cars, Garages etc. We are also more than happy to offer advice on suitability and installation of our products. Please keep checking our shop, as there are many more products to be added in the near future. We would also welcome your suggestions as to other products that you would like to see listed. Please ensure your details are correct. For Scottish Highlands, Islands and Non mainland Britain please ask us whether there is an additional cost before purchasing. Our aim is to provide an excellent service and this includes describing items for sale as accurately as possible. Please take a few moments to read all of the details, to make sure that the item you are ordering is exactly what you require. We are more than happy to answer any questions regarding these items and their suitability for your intended use.

]]> https://campervanvanmotorhome.com/2024/11/10a-pwm-lcd-usb-solar-charge-controller-x10-value-pack-10pc-motorhome-camper-van/feed/ 0 https://campervanvanmotorhome.com/2024/07/357mtr-dual-dc-dc-charger-split-charge-kit-euro-56-camper-van-motorhome-uk/ https://campervanvanmotorhome.com/2024/07/357mtr-dual-dc-dc-charger-split-charge-kit-euro-56-camper-van-motorhome-uk/#comments Tue, 30 Jul 2024 21:20:46 +0000 https://campervanvanmotorhome.com/2024/07/357mtr-dual-dc-dc-charger-split-charge-kit-euro-56-camper-van-motorhome-uk/


3/5/7MTR Dual DC-DC Charger / Split Charge Kit Euro 5/6 Camper Van Motorhome UK. 3/5/7 meters 12V 20Amp DC to DC Dual Battery Charger Kits With Built-in Solar MPPT Fit for Multiple battery types: AGM, GEL, Flooded, and Lithium, Idea for Caravan Camper Van Motorhome Boat. This powerful, high-quality battery to battery charger can charge a 12V battery from another 12V battery with its own power source, or from a solar panel using its built-in solar input PWM charge controller, at up to 20A. The fully-automatic battery charger uses an intelligent, multi-stage charging program that can be set to a wide variety of battery types using easy, one-button programming and features a full suite of electronic protections. This system is ideal for caravans, campervans, motorhomes or boats, where the alternator charging can be shared between the starter and leisure batteries while the engine is running, then the leisure battery can be kept topped up from solar power while the vehicle is parked. By combining two chargers into one unit the set-up and operation are made simple, allowing you to easily share an existing charging source between two batteries or battery banks and utilise solar power to extend your off-grid runtime. DC-DC Charger Key Features. Charge the leisure battery in two ways. DC Input from the (smart) alternator and the start battery or DC Input from the Solar Panel. Compatible with both conventional and smart alternators. (Euro5/6 Vehicle with variable output voltage). Compatible with Multiple battery types. AGM, GEL, Flooded, and Lithium. Solar panel regulator with Maximum Power Point Tracking. Bulk, Boost, and Float. Automatic battery separator works without the need for diodes or VSR relays. Starter battery maintenance charging when your service battery is fully charged. Battery isolation, over-voltage protection, battery temperature protection, over-current protection, overheat protection, reverse current protection, solar panel and alternator reverse polarity protection. With a soft-start charging program and a minimum output battery voltage of only 2.5V, this charger is capable of recovering batteries from extremely high depth of discharge. To show target battery charging stage, power source and selected battery type. Battery input voltage: 12.5 – 16.0V. Maximum charging current: 20A. Solar input voltage: 16.0 – 25.0V. Maximum solar input current: 20A. Minimum output battery voltage: 2.5V. Bulk charge voltage: 14.3V (AGM/Gel), 14.0V (Lead Acid), 15.0V (Calcium), 14.0V (Li-ion). Float charge voltage: 13.5V. Float charge current: 100mA. Battery capacity: 18 – 250Ah. Please note: The 3/5/7 mtrs of Red cable supplied in this kit are made up of the 4 separate leads which is ready made with connectors&heat shrink tubes. 3m kit includes everything you need for setup dual battery charging system. 12v 20amp DC to DC Charger. 2 x 250mm RED 70amp READY MADE cable from Battery to fuse holder lead. 1 x 500mm RED 70amp READY MADE cable Relay to fuse holder lead. 1 x 2 metre 70amp Relay to fuse holder READY MADE Lead. 1 metre 70amp of READY MADE Black Earth Lead. 1 Pair 8mm Post Type Battery Terminals. 2 x MTA MIDI Fuse holders. 4 x 60A MTA MIDI Fuses including 2 spares. Red&Black Heat shrink to protect all the connections. 10 x adhesive cable tie fixings base to keep everything tidy. Easy to understand Fitting Instructions + after sales support if required. 5m kit includes everything you need for setup dual battery charging system. 1 x 4 metre 70amp Relay to fuse holder READY MADE Lead. 7m kit includes everything you need for setup dual battery charging system. 1 x 6 metre 70amp Relay to fuse holder READY MADE Lead. We appreciate your business and strived to improve our customer service and our commitment to quality.

]]> https://campervanvanmotorhome.com/2024/07/357mtr-dual-dc-dc-charger-split-charge-kit-euro-56-camper-van-motorhome-uk/feed/ 0 https://campervanvanmotorhome.com/2022/09/camper-van-solar-panel-kit-100w-power-charge-controller-for-motorhome/ https://campervanvanmotorhome.com/2022/09/camper-van-solar-panel-kit-100w-power-charge-controller-for-motorhome/#comments Wed, 14 Sep 2022 16:29:25 +0000 https://campervanvanmotorhome.com/2022/09/camper-van-solar-panel-kit-100w-power-charge-controller-for-motorhome/










The junction box is waterproof with IP67. Built in blocking diode to prevent battery discharge at night. The solar panel is with 0.9m cable which is male and female connector. Stainless steel ring, durable and easy to install. 1 x 100 watt solar panel. 1 x 12 V / 24 V / 10 A solar controller. 1 x 3 m extension cabel with pv connector (2.5 mm²). 1 x 3 m extension cabel with alligator clips (2.5 mm²). This item is in the category “Vehicle Parts & Accessories\Caravan, Campervan & Motorhome Parts & Accessories\Other Caravan & Motorhome Parts & Accessories”. The seller is “bluecubeuk” and is located in this country: GB. This item can be shipped worldwide.

• Wattage: 100-199 W
• Pliability: Flexible
• System Configuration: Off-Grid
• Power: 100W
• Current Output: 10 A or Less
• Solar Technology: Monocrystalline
• Application: Automotive
• Charging Mode: PWM (Pulse Width Modulation)
• Power Source: Solar
• Resistance Properties: Dustproof
• Features: Flexible
• Voltage: 12 V
• Brand: Unbranded

]]> https://campervanvanmotorhome.com/2022/09/camper-van-solar-panel-kit-100w-power-charge-controller-for-motorhome/feed/ 0 https://campervanvanmotorhome.com/2020/05/t-max-dual-battery-system-split-charge-system-camper-van-motorhome-ba2685/ https://campervanvanmotorhome.com/2020/05/t-max-dual-battery-system-split-charge-system-camper-van-motorhome-ba2685/#comments Fri, 08 May 2020 05:28:12 +0000 http://campervanvanmotorhome.com/2020/05/t-max-dual-battery-system-split-charge-system-camper-van-motorhome-ba2685/


T-Max Dual Battery System / Split Charge System. With all the demands put on the battery of a camper / motorhome tv, stereo, laptop, auxillery heaters. The T-Max dual battery system automatically links the two batteries for charging, but isolates them when discharging. You also have the option to manually override the system to link the batteries for starting – especially useful in colder climates. This is a 12V system with a 250A load capacity. Kit contains: Solenoid, LED Display Unit, all the necessary Wiring and Connectors and Fitting Instructions. Pictures are for reference only and specifications may alter without notice. Product specifications are given but it is up to the end user to ensure that the product is fit for that purpose. Please leave a contact number when ordering. FREE CARRIAGE APPLIES TO MAINLAND UK ONLY. PLEASE SEE TERMS AND CONDITIONS FOR POSTCODE RESTRICTIONS. The item “T-Max Dual Battery System / Split Charge System Camper Van / Motorhome BA2685″ is in sale since Thursday, March 6, 2014. This item is in the category “Vehicle Parts & Accessories\Car Parts\Electrical Components\Other Electrical Components”. The seller is “foundry4x4″ and is located in Tredegar. This item can be shipped to United Kingdom, Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech republic, Denmark, Estonia, Finland, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Australia, United States, Canada, Japan, New Zealand, China, Hong Kong, Norway, Indonesia, Malaysia, Mexico, Singapore, South Korea, Switzerland, Taiwan, Thailand, Bangladesh, Belize, Bolivia, Brunei darussalam, Dominica, Ecuador, Guernsey, Gibraltar, Guadeloupe, Grenada, French guiana, Iceland, Jersey, Cambodia, Saint kitts and nevis, Liechtenstein, Macao, Monaco, Martinique, Nicaragua, Pakistan, Peru, Paraguay, Turks and caicos islands, Aruba, Saudi arabia, United arab emirates, Chile, Bahamas, Costa rica, Dominican republic, Guatemala, Honduras, Jamaica, Kuwait, Panama, Philippines, Qatar, El salvador, Trinidad and tobago, Uruguay, Viet nam, France.

• Intended Use: Modification/ Enhancement
• Manufacturer Part Number: BA 2685
• Brand: T Max
• Model/ Series: Defender
• Manufacturer: Land Rover
• Type: Batteries & Accessories

]]> https://campervanvanmotorhome.com/2020/05/t-max-dual-battery-system-split-charge-system-camper-van-motorhome-ba2685/feed/ 0