https://campervanvanmotorhome.com Mon, 06 Apr 2026 11:28:51 +0000 en-US hourly 1 https://wordpress.org/?v=4.1.1 https://campervanvanmotorhome.com/2025/12/led-skylight-dome-roof-vent-shower-hatch-motorhome-camper-van-caravan-580x580mm/ https://campervanvanmotorhome.com/2025/12/led-skylight-dome-roof-vent-shower-hatch-motorhome-camper-van-caravan-580x580mm/#comments Thu, 04 Dec 2025 04:47:45 +0000 https://campervanvanmotorhome.com/2025/12/led-skylight-dome-roof-vent-shower-hatch-motorhome-camper-van-caravan-580x580mm/










HIGH QUAILTY LED CAMPER VAN MOTORHOME HORSEBOX CARAVAN SKYLIGHT ROOF VENT 580mm x 580mm. This premium quality camper van skylight roof vent provides additional ventilation and natural light to your motorhomes making it an ideal accessory. Made from high quality materials, our roof vents provide you with protection from UV rays as well as high impact. Blackout blinds are also supplied alongside flynet screen providing you with protection and privacy from insects. Built in 12v Turbo Fan. Roof Vent Size is 580mm x 580mm. Manufactured with high quality materials. NOTE: THE CUT-OUT SIZE SHOULD BE 452mmx402mm. Place the internal cap (garnish) on top the roof and draw a template using a felt tip, then add another 5mm to the top and left side. Drill pilot holes in each corner and cut along the template line. Be certain to avoid ribs, braces, and electrical wiring (internally). Check that the internal cap fits through the aperture If not, cut out opening as needed and then smooth down any rough edges and primer the exposed with metal oxide paint. Make a wooden frame around the aperture to the thickness of the interned finish depth required, taking in to account the roof ply and lining. Glue the frame with Shield Stick and Seal (polyurethane) and clap in place and allow the adhesive to set. Screw the internal cap to the timber frame and seal around the lip from the top of the roof using flexible putty or Sikaflex. Place the external vent over the lip of the internal cap and mark the screw holes with a centre punch. Then remove vent from roof and drill all screw hole locations with a 1/16” pilot hole, and seal with primer paint. NOTE: If installing a power or lighted vent, provide power source of 12 volts DC, using 18-gauge wire. Place putty strips/ Sikaflex flex bead around the opening on roof. (1.27cm) from edge of opening. Be sure putty strips cover entire area to be sealed. Use double layers of putty strip or extra Sikaflex, if necessary, to seal ribbed areas. Insert vent into opening on top of putty strips. Use a screwdriver or nail to locate and line up corner drilled holes with the corner screw holes in vent frame. CAUTION: Install vent with lid hinge side toward front of vehicle. Screw corner screws first to hold vent in place then screw all remaining vent mounting screws. Tighten just enough to compress putty tape. Over-tightening may cause Plastic Base Vents to crack. Using the appropriate roof coating for your roof surface, coat screw heads and vent frame edge and seal around the frame if necessary. Your installation is complete If you are retrospectively fitting the roof vent you must take care when cutting the aperture as not to damage the existing head lining and leave enough to cover the timber frame if required. PLEASE NOTE: ALL ROOF VENTS SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN.

]]> https://campervanvanmotorhome.com/2025/12/led-skylight-dome-roof-vent-shower-hatch-motorhome-camper-van-caravan-580x580mm/feed/ 0 https://campervanvanmotorhome.com/2025/07/led-skylight-dome-roof-vent-motorhome-camper-van-caravan-horsebox-580x580mm/ https://campervanvanmotorhome.com/2025/07/led-skylight-dome-roof-vent-motorhome-camper-van-caravan-horsebox-580x580mm/#comments Fri, 04 Jul 2025 04:10:01 +0000 https://campervanvanmotorhome.com/2025/07/led-skylight-dome-roof-vent-motorhome-camper-van-caravan-horsebox-580x580mm/










HIGH QUAILTY LED CAMPER VAN MOTORHOME HORSEBOX CARAVAN SKYLIGHT ROOF VENT 580mm x 580mm. This premium quality camper van skylight roof vent provides additional ventilation and natural light to your motorhomes making it an ideal accessory. Made from high quality materials, our roof vents provide you with protection from UV rays as well as high impact. Blackout blinds are also supplied alongside flynet screen providing you with protection and privacy from insects. Built in 12v Turbo Fan. Roof Vent Size is 580mm x 580mm. Manufactured with high quality materials. NOTE: THE CUT-OUT SIZE SHOULD BE 452mmx402mm. Place the internal cap (garnish) on top the roof and draw a template using a felt tip, then add another 5mm to the top and left side. Drill pilot holes in each corner and cut along the template line. Be certain to avoid ribs, braces, and electrical wiring (internally). Check that the internal cap fits through the aperture If not, cut out opening as needed and then smooth down any rough edges and primer the exposed with metal oxide paint. Make a wooden frame around the aperture to the thickness of the interned finish depth required, taking in to account the roof ply and lining. Glue the frame with Shield Stick and Seal (polyurethane) and clap in place and allow the adhesive to set. Screw the internal cap to the timber frame and seal around the lip from the top of the roof using flexible putty or Sikaflex. Place the external vent over the lip of the internal cap and mark the screw holes with a centre punch. Then remove vent from roof and drill all screw hole locations with a 1/16” pilot hole, and seal with primer paint. NOTE: If installing a power or lighted vent, provide power source of 12 volts DC, using 18-gauge wire. Place putty strips/ Sikaflex flex bead around the opening on roof. (1.27cm) from edge of opening. Be sure putty strips cover entire area to be sealed. Use double layers of putty strip or extra Sikaflex, if necessary, to seal ribbed areas. Insert vent into opening on top of putty strips. Use a screwdriver or nail to locate and line up corner drilled holes with the corner screw holes in vent frame. CAUTION: Install vent with lid hinge side toward front of vehicle. Screw corner screws first to hold vent in place then screw all remaining vent mounting screws. Tighten just enough to compress putty tape. Over-tightening may cause Plastic Base Vents to crack. Using the appropriate roof coating for your roof surface, coat screw heads and vent frame edge and seal around the frame if necessary. Your installation is complete If you are retrospectively fitting the roof vent you must take care when cutting the aperture as not to damage the existing head lining and leave enough to cover the timber frame if required. PLEASE NOTE: ALL ROOF VENTS SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN.

]]> https://campervanvanmotorhome.com/2025/07/led-skylight-dome-roof-vent-motorhome-camper-van-caravan-horsebox-580x580mm/feed/ 0 https://campervanvanmotorhome.com/2024/12/820x620mm-camper-van-skylight-roof-vent-led-dome-motorhome-horsebox-caravan/ https://campervanvanmotorhome.com/2024/12/820x620mm-camper-van-skylight-roof-vent-led-dome-motorhome-horsebox-caravan/#comments Thu, 19 Dec 2024 21:10:56 +0000 https://campervanvanmotorhome.com/2024/12/820x620mm-camper-van-skylight-roof-vent-led-dome-motorhome-horsebox-caravan/











CAMPER VAN SKYLIGHT LED CRYSTAL DOME ROOF VENT 820x620mm. The camper can skylight roof vent provides additional ventilation and natural light to your motorhomes making it an ideal accessory. Made from high quality materials, our roof vents provide you with protection from UV rays as well as high impact. Also supplied alongside flynet screen providing you with protection and privacy from insects. Fitted With LED Lights. Double Glazed Dome Top. Maximum Opening to an angle of 60 Degrees. Vent Size is 820mm x 620mm. Manufactured with high quality materials. NOTE: THE CUT OUT SIZE SHOULD BE 702MM X 502MM. Place the internal cap (garnish) on top the roof and draw a template using a felt tip, then add another 5mm to the top and left side. Drill pilot holes in each corner and cut along the template line. Be certain to avoid ribs, braces, and electrical wiring (internally). Check that the internal cap fits through the aperture If not, cut out opening as needed and then smooth down any rough edges and primer the exposed with metal oxide paint. Make a wooden frame around the aperture to the thickness of the interned finish depth required, taking in to account the roof ply and lining. Glue the frame with Shield Stick and Seal (polyurethane) and clap in place and allow the adhesive to set. Screw the internal cap to the timber frame and seal around the lip from the top of the roof using flexible putty or Sikaflex. Place the external vent over the lip of the internal cap and mark the screw holes with a centre punch. Then remove vent from roof and drill all screw hole locations with a 1/16” pilot hole, and seal with primer paint. NOTE: If installing a power or lighted vent, provide power source of 12 volts DC, using 18-gauge wire. Place putty strips/ Sikaflex flex bead around the opening on roof ½” (1.27cm) from edge of opening. Be sure putty strips cover entire area to be sealed. Use double layers of putty strip or extra Sikaflex if necessary, to seal ribbed areas. Insert vent into opening on top of putty strips. Use an screw driver or nail to locate and line up corner drilled holes with the corner screw holes in vent frame. CAUTION: Install vent with lid hinge side toward front of vehicle. Screw corner screws first to hold vent in place then screw all remaining vent mounting screws. Tighten just enough to compress putty tape. Over-tightening may cause Plastic Base Vents to crack. Using the appropriate roof coating for your roof surface, coat screw heads and vent frame edge and seal around the frame if necessary. Your installation is complete If you are retrospectively fitting the roof vent you must take care when cutting the aperture as not to damage the existing head lining and leave enough to cover the timber frame if required. PLEASE NOTE: ALL ROOF VENTS SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN. If there’s a problem please don’t hesitate to message us, we promise to get it resolved.

]]> https://campervanvanmotorhome.com/2024/12/820x620mm-camper-van-skylight-roof-vent-led-dome-motorhome-horsebox-caravan/feed/ 0 https://campervanvanmotorhome.com/2024/11/led-skylight-dome-roof-vent-motorhome-camper-van-caravan-horsebox-835x645mm/ https://campervanvanmotorhome.com/2024/11/led-skylight-dome-roof-vent-motorhome-camper-van-caravan-horsebox-835x645mm/#comments Sat, 02 Nov 2024 17:24:10 +0000 https://campervanvanmotorhome.com/2024/11/led-skylight-dome-roof-vent-motorhome-camper-van-caravan-horsebox-835x645mm/










HIGH QUAILTY LED CAMPER VAN MOTORHOME HORSEBOX CARAVAN SKYLIGHT ROOF VENT 835mm x 645mm. This premium quality camper van skylight roof vent provides additional ventilation and natural light to your motorhomes making it an ideal accessory. Made from high quality materials, our roof vents provide you with protection from UV rays as well as high impact. Blackout blinds are also supplied alongside flynet screen providing you with protection and privacy from insects. Built in 12v Turbo Fan. Roof Vent Size is 835mm x 645mm. Manufactured with high quality materials. NOTE: THE CUT-OUT SIZE SHOULD BE 702mm x 502mm. Place the internal cap (garnish) on top the roof and draw a template using a felt tip, then add another 5mm to the top and left side. Drill pilot holes in each corner and cut along the template line. Be certain to avoid ribs, braces, and electrical wiring (internally). Check that the internal cap fits through the aperture If not, cut out opening as needed and then smooth down any rough edges and primer the exposed with metal oxide paint. Make a wooden frame around the aperture to the thickness of the interned finish depth required, taking in to account the roof ply and lining. Glue the frame with Shield Stick and Seal (polyurethane) and clap in place and allow the adhesive to set. Screw the internal cap to the timber frame and seal around the lip from the top of the roof using flexible putty or Sikaflex. Place the external vent over the lip of the internal cap and mark the screw holes with a centre punch. Then remove vent from roof and drill all screw hole locations with a 1/16” pilot hole, and seal with primer paint. NOTE: If installing a power or lighted vent, provide power source of 12 volts DC, using 18-gauge wire. Place putty strips/ Sikaflex flex bead around the opening on roof. (1.27cm) from edge of opening. Be sure putty strips cover entire area to be sealed. Use double layers of putty strip or extra Sikaflex, if necessary, to seal ribbed areas. Insert vent into opening on top of putty strips. Use a screwdriver or nail to locate and line up corner drilled holes with the corner screw holes in vent frame. CAUTION: Install vent with lid hinge side toward front of vehicle. Screw corner screws first to hold vent in place then screw all remaining vent mounting screws. Tighten just enough to compress putty tape. Over-tightening may cause Plastic Base Vents to crack. Using the appropriate roof coating for your roof surface, coat screw heads and vent frame edge and seal around the frame if necessary. Your installation is complete If you are retrospectively fitting the roof vent you must take care when cutting the aperture as not to damage the existing head lining and leave enough to cover the timber frame if required. PLEASE NOTE: ALL ROOF VENTS SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN.

]]> https://campervanvanmotorhome.com/2024/11/led-skylight-dome-roof-vent-motorhome-camper-van-caravan-horsebox-835x645mm/feed/ 0 https://campervanvanmotorhome.com/2024/09/led-skylight-dome-roof-vent-motorhome-camper-van-caravan-horsebox-580mmx580mm/ https://campervanvanmotorhome.com/2024/09/led-skylight-dome-roof-vent-motorhome-camper-van-caravan-horsebox-580mmx580mm/#comments Tue, 03 Sep 2024 01:40:45 +0000 https://campervanvanmotorhome.com/2024/09/led-skylight-dome-roof-vent-motorhome-camper-van-caravan-horsebox-580mmx580mm/










HIGH QUAILTY LED CAMPER VAN MOTORHOME HORSEBOX CARAVAN SKYLIGHT ROOF VENT 580mm x 580mm. This premium quality camper van skylight roof vent provides additional ventilation and natural light to your motorhomes making it an ideal accessory. Made from high quality materials, our roof vents provide you with protection from UV rays as well as high impact. Blackout blinds are also supplied alongside flynet screen providing you with protection and privacy from insects. Built in 12v Turbo Fan. Roof Vent Size is 580mm x 580mm. Manufactured with high quality materials. NOTE: THE CUT-OUT SIZE SHOULD BE 452mmx402mm. Place the internal cap (garnish) on top the roof and draw a template using a felt tip, then add another 5mm to the top and left side. Drill pilot holes in each corner and cut along the template line. Be certain to avoid ribs, braces, and electrical wiring (internally). Check that the internal cap fits through the aperture If not, cut out opening as needed and then smooth down any rough edges and primer the exposed with metal oxide paint. Make a wooden frame around the aperture to the thickness of the interned finish depth required, taking in to account the roof ply and lining. Glue the frame with Shield Stick and Seal (polyurethane) and clap in place and allow the adhesive to set. Screw the internal cap to the timber frame and seal around the lip from the top of the roof using flexible putty or Sikaflex. Place the external vent over the lip of the internal cap and mark the screw holes with a centre punch. Then remove vent from roof and drill all screw hole locations with a 1/16” pilot hole, and seal with primer paint. NOTE: If installing a power or lighted vent, provide power source of 12 volts DC, using 18-gauge wire. Place putty strips/ Sikaflex flex bead around the opening on roof. (1.27cm) from edge of opening. Be sure putty strips cover entire area to be sealed. Use double layers of putty strip or extra Sikaflex, if necessary, to seal ribbed areas. Insert vent into opening on top of putty strips. Use a screwdriver or nail to locate and line up corner drilled holes with the corner screw holes in vent frame. CAUTION: Install vent with lid hinge side toward front of vehicle. Screw corner screws first to hold vent in place then screw all remaining vent mounting screws. Tighten just enough to compress putty tape. Over-tightening may cause Plastic Base Vents to crack. Using the appropriate roof coating for your roof surface, coat screw heads and vent frame edge and seal around the frame if necessary. Your installation is complete If you are retrospectively fitting the roof vent you must take care when cutting the aperture as not to damage the existing head lining and leave enough to cover the timber frame if required. PLEASE NOTE: ALL ROOF VENTS SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN.

]]> https://campervanvanmotorhome.com/2024/09/led-skylight-dome-roof-vent-motorhome-camper-van-caravan-horsebox-580mmx580mm/feed/ 0 https://campervanvanmotorhome.com/2024/09/led-skylight-dome-roof-vent-shower-hatch-motorhome-camper-van-caravan-835x645mm/ https://campervanvanmotorhome.com/2024/09/led-skylight-dome-roof-vent-shower-hatch-motorhome-camper-van-caravan-835x645mm/#comments Mon, 02 Sep 2024 13:39:45 +0000 https://campervanvanmotorhome.com/2024/09/led-skylight-dome-roof-vent-shower-hatch-motorhome-camper-van-caravan-835x645mm/










HIGH QUAILTY LED CAMPER VAN MOTORHOME HORSEBOX CARAVAN SKYLIGHT ROOF VENT 835mm x 645mm. This premium quality camper van skylight roof vent provides additional ventilation and natural light to your motorhomes making it an ideal accessory. Made from high quality materials, our roof vents provide you with protection from UV rays as well as high impact. Blackout blinds are also supplied alongside flynet screen providing you with protection and privacy from insects. Built in 12v Turbo Fan. Roof Vent Size is 835mm x 645mm. Manufactured with high quality materials. NOTE: THE CUT-OUT SIZE SHOULD BE 702mm x 502mm. Place the internal cap (garnish) on top the roof and draw a template using a felt tip, then add another 5mm to the top and left side. Drill pilot holes in each corner and cut along the template line. Be certain to avoid ribs, braces, and electrical wiring (internally). Check that the internal cap fits through the aperture If not, cut out opening as needed and then smooth down any rough edges and primer the exposed with metal oxide paint. Make a wooden frame around the aperture to the thickness of the interned finish depth required, taking in to account the roof ply and lining. Glue the frame with Shield Stick and Seal (polyurethane) and clap in place and allow the adhesive to set. Screw the internal cap to the timber frame and seal around the lip from the top of the roof using flexible putty or Sikaflex. Place the external vent over the lip of the internal cap and mark the screw holes with a centre punch. Then remove vent from roof and drill all screw hole locations with a 1/16” pilot hole, and seal with primer paint. NOTE: If installing a power or lighted vent, provide power source of 12 volts DC, using 18-gauge wire. Place putty strips/ Sikaflex flex bead around the opening on roof. (1.27cm) from edge of opening. Be sure putty strips cover entire area to be sealed. Use double layers of putty strip or extra Sikaflex, if necessary, to seal ribbed areas. Insert vent into opening on top of putty strips. Use a screwdriver or nail to locate and line up corner drilled holes with the corner screw holes in vent frame. CAUTION: Install vent with lid hinge side toward front of vehicle. Screw corner screws first to hold vent in place then screw all remaining vent mounting screws. Tighten just enough to compress putty tape. Over-tightening may cause Plastic Base Vents to crack. Using the appropriate roof coating for your roof surface, coat screw heads and vent frame edge and seal around the frame if necessary. Your installation is complete If you are retrospectively fitting the roof vent you must take care when cutting the aperture as not to damage the existing head lining and leave enough to cover the timber frame if required. PLEASE NOTE: ALL ROOF VENTS SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN.

]]> https://campervanvanmotorhome.com/2024/09/led-skylight-dome-roof-vent-shower-hatch-motorhome-camper-van-caravan-835x645mm/feed/ 0 https://campervanvanmotorhome.com/2024/05/autoshield-camper-van-clear-dome-skylight-roof-vent-motorhome-hatch-500x500mm/ https://campervanvanmotorhome.com/2024/05/autoshield-camper-van-clear-dome-skylight-roof-vent-motorhome-hatch-500x500mm/#comments Mon, 13 May 2024 11:00:29 +0000 https://campervanvanmotorhome.com/2024/05/autoshield-camper-van-clear-dome-skylight-roof-vent-motorhome-hatch-500x500mm/











Add to favourite sellers. CLEAR SKYLIGHT DOME ROOF VENT 500X500 (OVERALL SIZE). Easy operation with gas lift struts. Double glazed dome top. Maximum opening to an angle of 60° with three opening positions. Interior frame with black out blind and fly net screen. Up to 150 cubic centre meters of permanent ventilation. The Shield Autocare skylight dome roof vent is an ideal accessory if your motorhome, camper van or horse box requires additional ventilation and light. It is an ideal product for venting small compact spaces and providing extra natural light to your area. Our roof vents are made from superior quality impact and UV resistant materials. Supplied with blackout blinds and flynet screen if you would like privacy and protection from insects. Cut out size: 400mm x 400mm. Overall top lid size: 500mm x 500mm approx. Overall internal blind size: 520mm x 520mm approx. Open in 3 positions: front tilt, back tilt and fully open. Comes with fly net screen and blind system which can be set at various positions. Clear dome to allow maximum light to pass in to vehicle. Here at Shield Autocare we specialise in accessories for nearly anything with wheels! Whether that is you car, van, Motorhome, campervan or bike, we believe in protecting and enhancing what you love. Having been in the Automotive industry for 19 years, we are able to use the knowledge and experience to bring you the highest quality accessories at great prices with most of our products being tried and tested for years with thousands of positive reviews. We also manufacture our own products and are always setting the standard for new and innovative products so rest assured you are getting the latest and best. Send us a Message.

]]> https://campervanvanmotorhome.com/2024/05/autoshield-camper-van-clear-dome-skylight-roof-vent-motorhome-hatch-500x500mm/feed/ 0 https://campervanvanmotorhome.com/2023/03/can-sink-387-dia-stainless-steel-dome-bowl-boatcamper-vanmotorhomecaravan/ https://campervanvanmotorhome.com/2023/03/can-sink-387-dia-stainless-steel-dome-bowl-boatcamper-vanmotorhomecaravan/#comments Sat, 18 Mar 2023 16:43:00 +0000 https://campervanvanmotorhome.com/2023/03/can-sink-387-dia-stainless-steel-dome-bowl-boatcamper-vanmotorhomecaravan/


CAN SINK 387 DIA STAINLESS STEEL DOME BOWL – Boat / Camper van / Motorhome / Caravan. 387mm Diameter x 155mm Deep (Concave). This item is in the category “Vehicle Parts & Accessories\Caravan, Campervan & Motorhome Parts & Accessories\Other Caravan & Motorhome Parts & Accessories”. The seller is “caravan-accessories” and is located in this country: GB. This item can be shipped worldwide.

• Type: Kitchen Equipment
• Sub-Type: Sink Units
• Manufacturer Part Number: CLA1440
• Brand: CAN

]]> https://campervanvanmotorhome.com/2023/03/can-sink-387-dia-stainless-steel-dome-bowl-boatcamper-vanmotorhomecaravan/feed/ 0